Caution: Be sure to turn o hot and cold water supplies
before installing or servicing faucet.
Installation Procedure
Push valve bodies through holes in sink from 1.
underneath. Make sure mounting nuts (RT-103N) are
on underside of sink. Valve marked Hot is on the le
and Cold is on the right. Put gasket (LN-129) over valve
body. read escutcheon (LN-128) onto valve bodies.
e top of the valve spindle should measure 1-7/8” from
mounting surface (See rough in drawing).
read collar (LN-112) on to valve body until it reaches 2.
the escutcheon (LN-128). Tighten mounting nuts from
underneath sink.
CRP handle installation: Place lever part of handle on 3.
valve spindle and thread screw (LN-121A) into valve.
Install spout (LN-254A) and centerbody (LN-188) 4.
through center in sink hole from above sink. Secure
spout to sink with washer (LN-138A) and nut (SPF-26).
Washer (LN-138A) at should face back of the sink.
read tee (LN-189) to bottom of centerbody (LN-188).
read ex hoses (LN-157) into tee (LN-189) using pipe 5.
dope or te on tape on the pipe threads. read other
end on to valve bodies.
Connect hot supply to le tube and cold supply to right 6.
tube using appropriate connectors.
Pop-up drain installation:7.
Remove pop-up plug, tail piece and ange from a )
the drain body. Make sure that locknut is threaded
all the way down onto the body with at friction
washer in middle and beveled washer on top.
Apply plumbers putty or sealant to bottom of b )
ange.
Install drain body through drain opening in c )
lavatory and screw ange onto the drain body
making sure that the threads are completely
engaged for proper sealing and strength of the
connection. Apply joint compound to all threaded
parts to insure
proper seal.
Tighten locknut to compress the beveled ange d )
evenly across the bottom of the drain opening taking
care not to over tighten the locknut, causing damage
to the lavatory. Apply te on tape (clockwise) on tail
piece and thread into outlet of body.
Insert pop-up plug and pivot rod into body and e )
tighten retaining nut until the ball is seated on the
ball washer.
Note: e pop-up plug can be installed either in the
removable or non-removable position, depending
on the location of the hole located in the guide at
the bottom of the plug.
Slide the pivot rod through one side of the spring f )
clip, then the appropriate adjustment hole and then
other side of the spring clip.
Insert li rod through faucet housing and the top of g )
the li strap and secure it in place by tightening the
screw.
Note: To insure proper operation of li rod and
pop-up, some adjustment of the linkage may be
required.
ere are two possible adjustment points:
1) li strap to li rod
2) li strap to pivot rod.
It is very important to thoroughly ush the supply lines 8.
to prevent foreign matter, i.e. copper chips, sand, stones,
etc. from damaging the sealing surfaces of cartridge.
Remove aerator and open hot and cold to full open then
open both supplies. Let water run through hot and cold
long enough to ush supply lines thoroughly. Shut o
faucet and replace aerator. Check for leaks.
Replacing cartridge (KN-113 or KN-114):
Remove plug button (LN-243H or LN-243C), loosen 1.
Philip head screw (LN-121A) and remove handle (LN-
177).
Remove collar (LN-112) by turning counter clockwise.2.
Caution: Do not use wrench as this may damage the
surface nish.
Place wrench on cartridge hex nut (KN-113, KN-114). 3.
Turn wrench counter clockwise until cartridge is
removed.
Install new cartridge. Turn cartridge with wrench until 4.
cartridge does not turn easily then turn 1/4 to 1/2 turn
further. Reassemble handle in reverse fashion.
Widespread Lavatory Faucet SLW-4412
Installation and Service Instructions
Carrington™
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals